Відео

Genius

What about pin switch settings?

Hi Zep, I have tried your app and got connection to my 8266. I can get grbl comms and send and receive and I can send commands but when I use the step buttons I just get error 22. If I enter grbl move command like g0 x10 f100 it works fine. Any help would be awesome. Thanks

I hope you'll come back soon with some new and cool stuff! I love your channel!

Would it be possible to make 3-4 of these panels, and sync 3-4 controllers?.. for bigger screen, and more resoultion?

I miss your presence on youtube. I hope you are doing well. Cheers

Could you send me a photo of your setup for the 6 switches on the tb6600 as I am unsure , I have the same machine and have everything re wired Enjoyed your video

I got a lot more lucky, mine 3040 has the separate drivers from factory

Seriously, stop wasting everyone's time.

thnx

I want to make more bigger display, but I am not sure about fps, that if last LED will updated with the same fps or I will have to decrease the fps...

😂😂😂😂

4 years old video no captioning how can i under stand what you said about it

6:56 "boop" is literally what the arduino says to the 54HC595! 😂 EDIT - Excellent video. Esp. the detailed explanations on how the chips work using the datasheets.

How do i tell marlin to swich the negative side in stead of possitive side? My board is maxed out at 3.3 volts so i want to put constand 5 volt to all the positive sides and swich the negative. Is this possible in marlin?

❤❤❤ I can't say anything about it u r a good teaching❤❤❤ love u from India. assam....

What yer smoking there, buddy? 😂

i dont find a wifi controller for android

Hi i am using ramps and lcd with my homemade cnc in same way but i have a problem when i store leveling data to eeprom and activate the bed leveling i send g1 z0 commande to go to zero z but it given me the wrong calibration, i must send m851 z0 ?

The awful music killed it for me.

Just in case, you can also use Windows Notepad and Ctrl+H and replace all E with A in one click.

Stunning. Wish you showed how to connect or wired those 4 pins LEDs

Hi, but using fluidNC I can monitoring the cnc for example when start, stop, wait, allarm, type allarm, ecc? And I can also send the gcode? Please help me

Nice, very nice. 😁

I've done similar, but using an Arduino MEGA as the reader, wiring address pins to the to the upper i/o pins, and the data pins to the last 8.

Hi, great proyect, maybe the drawings of the structure?, measures, i see in instructables, but stay only the videos, can help me, thanks friend

Thank you for sharing but it was messed up with the comment about the Arabs, by the way if it's not for the Arabs you be today grinding stones with your teeth my friend, the Arabs developed the civilisation that is born today through the semiconductor that you using which base zero and one binary numbers, imagine yourself doing all the algorithms with Roman number. Be grateful to the dedicated scientist that paved the way to today's technology.

Such an informative, concise and entertaining Video! Keep up the great work! :)

Loved the shoes.

where is the fourth axis ? You are using 3 axis

Nice video. Did you make another one on writing EPROMs ?

cool bro

Really good videos. Love this bandsaw.

Olá amigo essa controladora passa imagens e vídeos perfeitamente?

Nice job but you can also make it easier to assemble if you dint cut all the way thru the material. Leave .015 and just fold it into a box with glue in the joints and presto no outer seems to show Try it sometime it works really well

Is that the Vevor 3040 Machine?

La verdad no me gustó todo estaba bien hasta que le pusiste tapas de madera ,todo de metal está bien pero con madera se ve feo

Hello I been a long time watcher of your Chanel and I was wondering if you could make another video on this to run on the ramps 1.4 or the mks gen l v1.0 motherboard because that is a ramps 1.4 motherboard all in one thank you for your time.

Some serious voltage drop happening here. The reason is because you wired them all in series. You need to give each matrix power in parallel (that's why they have the 2 extra power cords). Only the data should be in series, with a 300-500 ohm resistor before your first LED.

Yes. I now have discovered the original Designer of this Router. Life Latitudes copied from you.

Like por la entrada.

Send the code pls

I have taken apart about 8 dvd players within the last week. Only one laser has worked and the rest dead as door nail. After the 6th one it came to me to check the dvd player, plug it in, put a dvd disc in it. Take off the top cover and check to see if the laser comes on. Both the 7th and the 8th dvd player the laser was on , no problems. So I took them out, wire them and absolutely nothing. I don't know which pin is hot + and which are ground, common or whatever. Some of them the pins are in a straight line instead of in triangle. So it came to me to check the pins of the one that actually works. I put the multimeter on diode mode, forward voltage thing. The diode that works, the pins are in triangle. I checked the outer pins and the foward voltage from one to the other is 2.9V and when testing it, the laser although weak actually comes on which makes sense. while no reading if connected the opposite. NO forward voltage reading between any other combination including the middle pin, nor do I read any ohm readings. With the other two last diodes I took out, the pins are in straight line. The only reading I get is forward voltage reading betwee one end pin and the middle pin but 1.5V. There is no voltage readings between the outer pins. The same with all the other ones that don't work, regardless if the position of the pins are traiangular or in a stragiht line. I am so stressed.

hi, i have 3040Z-DQ, 3 axis, 500w air spindle, with pw3618 spindle controler and nt65-3x controler same as on this video. In few months ago, starting to have problems with pw3618 then with nt65. I,m asking does this changes will work in mach3

Silly intro

Need to applicate the yellow lights around the table

Amazing! Is there a way to add audio reactive microphone into a setup similar to this using the T8000 Controller

so i will be starting here!!

tysm i want to try and do this!!

Dude, this is amazing !! It's possible to replace any CCFL backlight, with RGBW LEDs in this way? (to improve the color and contrast, connected to a VGA or another HDMI and put "mirror display" in Windows configuration) have you ever tried something like this with an old LCD? Thank you. ps: Year 2022, there is any new and better controller & LEDs?